Special
|
- FUEL LINE DISCONNECT TOOL
- It works on 5/16" and 3/8" fuel lines found on GM, Ford and Chrysler. KDT-3321 KD tools $16.21. OTC-7660 OTC $14.95.
- KDT-3290 K-D TOOLS FORD A/C SPRING LOCK TOOL- $15.45
- Works on most Ford air conditioning and fuel lines with spring lock couplers sizes 3/8", 1/2", 5/8" and 3/4'
- LIS-37000 LISLE A/C FUEL LINE DISCONNECT TOOL SET- $9.95
- It works on GM, Ford, & Chrysler quick connect lines in sizes 5/16", 3/8", 1/2", 5/8", 3/4", and 7/8". Six pieces to set.
- OTC-7363 OTC FUEL LINE DISCONNECT TOOL SET- $19.95
- Two tool line disconnect tools and two spring lock coupler tools for easily disconnecting the spring lock couplings on Ford's popular port fuel injection system, as well as quick connect fuel lines on other Fords, GM, and Chrysler with 5/16", 3/8" and 1/2" OD. Won't damage the fuel line or connector.
- THX-354 THEXTON FUEL/IGNITION TROUBLESHOOTER- $24.29
- Helps diagnose cause of engine hesitation, failure to start, missing, etc. Isolates problem to either fuel or ignition system. Special test adapter fits between spark plug and spark plug wire. Attached five foot test leads connect to neon indicator light. Suction cup holds light firmly on windshield. When test driving vehicle, light will flash continuously if ignition system is working properly, check fuel system for problem. If light does not flash continuously, problem is in the ignition system.
- THEX-361 THEXTON GM FUEL INLET NUT WRENCH- $14.25
- Specially designed wrench is angled to allow use of two wrenches side-by-side. Fits all 1" GM fuel inlet nuts. 12 point open jaw slips over fuel lines up to 3/8". Hardened steel with vinyl grip.
- THX-312 THEXTON PLUG ALL VACUUM & FUEL LINE STOPPERS- $7.91
- Stepped design fit all 1/8", 3/16" 1/4", 5/16", 3/8" and 1/2" hoses. Tapered caps close tubes from 1/8" to 1/2". Use during tune-ups, vacuum tests, fuel pump repairs and more. Bead chain prevents loss.
- THX-393 THEXTON UNIVERSAL THROTTLE PEDAL DEPRESSOR- $34.27
- Easily attaches to steering wheel and pedal of all cars and most trucks. Eliminates need to remove air cleaner assembly. Quickly adjusts RPM to desired setting. Useful for air conditioning work, cylinder tests, tune-ups and brake jobs.
- LIS-55700 LISLE MASTER FUEL INJECTION TEST SET
- Test all types of fuel injection systems. Set checks fuel pressure on most port fuel injection (PFI) and throttle body injection (TBI) systems. Comes with a variety of adapters and gauges for checking many types of systems. Adapts to work with test port connections, end of hose connections and in-line connections. Tests GM, Ford, Chrysler, Honda/Accura, Toyota, Bosch CIS and L- Jetronic. List of component parts included with instructions.
- Back To The Top Of The Page
1.FUEL LINE TOOLS
- THX-801 THEXTON GM IDLE MIXTURE ADJUSTING KIT- $17.99
- Fits all 1979 and up GM carburetors. Contains THX-350 Idle Mixture Adjusting Tool and THX-353 Idle Mixture Seal Plug Remover. Plug removal tool removes plug covering idle mixture screw. Eliminates possible carburetor damage. Fits 3/8" drill chuck. Built-in stop allows cutting to proper depth. Removes plugs neatly and proffesionaly. Idle mixture removing tool is two tools in one. Fits Double D and 4.5mm hex. Flexable shaft for adjusting hard-to-reach screws. Sliding handle fits snugly onto either end of tool.
- GM IDLE ADJUSTING TOOLS
- Two tools in one. Flexible shaft for hard-to-reach screws. For all 1979 and up GM carburetors. Fits idle/mixture screws. One end fits Double D adjusting screws and the other fits 4.5mm hex adjusting screws. Sliding hex handle for firm grip. Overall length 9". ATD-5625 ATD TOOLS($7.58), THX-360 THEXTON.
- THX-362 THEXTON GM COMPUTER CONTROLLED CARBURETOR TOOLS- $13.37
- For2mm, 7mm, 10mm Double D and 2.5mm hex fittings. Tolls fit Varajet, Dualjet and Quadrajet carburetors. Adjusts or removes TPS, idle air bleed, mixture control solenoid and main metering jets. For use with 7/16" and 1/2" deepwell sockets.
- THX-358 THEXTON FORD/CHRYSLER/IMPORTS IDLE MIXTURE ADJUSTING TOOL- $7.49
- Fits 1981 and up Ford, Chrysler and some imports. Makes adjusting idle mixture screws fast and easy. Flexible shaft for hard-to-reach screws. One end for straight slotted and one end for 3/32" hex screws. Sliding handle fits snugly in either end of tool.
- THX-353 THEXTON GM IDLE MIXTURE SEAL PLUG REMOVER- $11.65
- Works on 1979 and up GM cars. Removes plug easily and neatly. Improved design resists breakage. Tool fits 3/8" drill chuck and has built-in stop for correct depth of cut. Eliminates damage to carburetor caused by using hammer and punch. Hardened steel with black oxide finish.
- THX-379 THEXTON GM & FORD CARBURETOR IDLE MIXTURE ADJUSTING SOCKETS- $12.21
- Sockets fit all 1979 and up GM and 1981 and up Ford carburetors. Sockets fit GM Double D, GM 4.5mm hex and Ford 3/32" hex adjusting screws. Sockets snap on to all 1/4" drive, fixed or flexible drivers.
- LIS-55250 LISLE CARBURETOR ADJUSTING TOOL- $12.95
- For adjusting idle/mixture screws on GM and Chrysler. Heavy duty 11" flexible shaft for easy access. Drive and shaft are securely crimped, won't come loose. Four adapters conveniently store in the hollow handle.
- THX-380 THEXTON GM COMPUTER CONTROLLED CARBURETOR SOCKETS- $20.99
- Sockets fit Varajet, Dualjet and quadrajet computer controlled carburetors. Sockets include 2.5mm hex, 7mm Double D, 10mm Double D, and 2mm Double D. For use with any 1/4" drive tool.
- KDT-2776 K-D TOOLS GM CARBURETOR ADJUSTING TOOL- $11.52
- Easily adjusts C-4 carburetor idle mixture screws on late model GM's including X-Body. Flexible shaft lets you reach hard-to-get-at screws. Reversible bit fits Double D and hex head screws.
- THX-370 THEXTON GM COMPUTER COMMAND CARBURETOR GAUGE KIT- $10.98
- provides three gauges for adjusting CCC Rochester Dualjet and Quadrajet carbs. Gauges accurately measures travel of mixture control solenoid plunger so lean stop, rich stop and idle air bleed valve can ba adjusted. Kit has Solenoid Gauge, Idle Air Bleed Valve Gauge and Float Scale. Instructions included.
- THX-348 THEXTON VACUUM LINE IDENTIFIERS- $15.31
- Contains six sets of matching plugs and caps. Colored sets eliminates incorrect hook-ups. Speeds work on emission controls, engine rebuilding and work on heads. Made of natural rubber with locking storage ring.
- THX-372 THEXTON GM CHOKE ANGLE GAUGE- $20.49
- For precision adjustments of choke valve angle for all late model 2 barrel and 4 barrel GM carburetors.
- KDT-2539 K-D TOOLS CARBURETOR/DISTRIBUTOR ADJUSTING TOOL- $9.43
- Adjust carburetor mixture and idle speed with screwdriver bit. Hooded end keeps screwdriver from slipping. Use 1/8" hex bit for Delco-Remy external distributor adjustments. Non-kink flexible shaft lets you reach around obstructions. Shock-resistant plastic handle.
- LIS-46500 LISLE CARBURETOR PIN TOOL
- For fast, sure removal and installation of carburetor linkage pins. Also for "E" clips and other small parts.
- Back To The Top Of The Page
- ATD-8127 ATD HIGH ENERGY IGNITION GAUGE- $2.50
- Eight sizes .035", .040", .044", .045", .048", .050", .060", .080" and two electrode adjusting tools. Metric equivalents shown.
- ATD-8122 ATD IGNITION GAUGE- $2.27
- Seventeens blades 1-3/4" x 1/4". Sizes .010", .012", .013", .015", .016", .017", .018", .019", .020", .022", .024", .025", .026", .028", .030", .032", .035". Metric equivalents shown.
- ATD-8123 ATD OVERHEAD VALVE GAUGE- $2.55
- Twelve 4" offset blades in sizes .008", .010", .012", .013", .014", .015", .016",.018", .019", .020", .025", .026". Metric equivalents shown.
- ATD-8121 ATD MASTER FEELER GAUGE- $5.93
- Thirty-two straight blades in sizes .0015" to .035" including .010" brass blade for transistorized ignitions.
- KDT-163 K-D TOOLS VALVE TAPPET FEELER GAUGE-$4.80
- Eleven offset blades in sizes.008", .010", .012", .013", .014", .015", .016", .018", .019", .020", .026".
- KDT-161 K-D TOOLS DELUXE FEELER GAUGE-$7.66
- Thirty-two straight blades in sizes .0015" to .035" including .010" brass blade for transistorized ignitions.
- LIS-68100 LISLE DELUXE FEELER GAUGE- $7.95
- Thirty-one blades from .0015" to .035" plus one brass blade .010". Blades are 3-1/2" x 1/2".
- KDT-162 K-D TOOLS FEELER GAUGE- $4.99
- One 2-1/2" rule and fifteen straight blades in sizes .002", .003", .004", .005", .006", .008", .011", .012", .013", .0124", .016", .018", .020", .022", and .025"
- KDT-2062 K-D TOOLS MINI FEELER GAUGE- $4.66
- Sixteen straight blades 1/4" x 1-3/4" in sizes .010", .012", .015", ,016", .017", .018", .019", .020", .022", .024', .025", .026", .028", .030", .032", .035".
- KDT-2274 K-D TOOLS DELUXE METRIC FEELER GAUGE- $9.07
- Twenty-five blades in sizes .04, .05, .06, .07, .08, .09, .10, .15, .20, .25, .30, .40, .45, .50, .55, .60, .65, .70, .75, .80, .85, .90, .95, and 1.00mm.
- KDT-3293 K-D TOOLS SPARK PLUG GAP GAUGE- $2.58
- Ciculate coin-type ramp gauge easily measures spark plug gaps ranging from .020" to 100" or 0.6mm - 2.4mm.
- SPARK PLUG WIRE GAUGE
- These tools all have wire sizes: .025", .034", .040" and .054" to work on all standard ignition systems. ATD-8124 ATD Tools($1.95), KDT-166 KD Tools($2.66), LIS-67800 Lisle($2.10).
- KDT-2327 K-D TOOLS WIDE GAP SPARK PLUG GAUGE- $2.44
- Measures sizes .040", .044", .045", .050", .060" and .080". Metric equivalents shown
- KDT-165 K-D TOOLS SPARK PLUG WIRE GAUGE- $4.54
- Eight wire in sizes .020", .025", .028", .030", .032", .034", .035" and .040" with electrode adjusting tool.
- KDT-2223 K-D TOOLS NON-MAGNETIC FEELER GAUGE- $2.67
- For electronic ignitions. Six blade sizes - .006", .008", .010", .012", .014" and .016". Metric equivalents shown.
- KDT-2424 K-D TOOLS GO-NO-GO FEELER GAUGE- $11.32
- Prevents errors while doing ignition point setting or tappet adjusting. Gauges includes twenty-two rust resistant blades ranging from .004" to .027" (.10mm to .69mm) with a .002" step ground on each blade for precise settings.
- KDT-164 K-D TOOLS TOOLS COMBINATION GAUGE- $6.81
- Six spark plug gap wires. Twelve straight blades and an electrode adjusting tool. Metric equivalents shown.
- Back To The Top Of The Page
- LIS-14900 LISLE TERMINAL TOOL- $13.95
- For GM C3 systems. Six tools in one-flat blade to open connectors, fork for ALDL connectors, three rectangular blades for Pack-Con terminals, spring-loaded tube for Weather-Pack terminals. Removes wires from most GM and American Motors computer connectors. Makes removal faster and easier. Eliminates damage to wires and terminals.
- LIS-56500 LISLE TERMINAL TOOL- $11.95
- Designed to help the mechanic remove wires easily from terminal blocks without damage to either the wires or terminal. Compact for ease in handling and fits most common sizes of terminal blocks of domestic makes and models, plus some imports. The prongs extending from the star shaped tool depresses the barbs on the wire fitting to allow removal from the terminal block.
- LIS-55200 LISLE FUSE PULLER- $1.95
- Removes both glass and blade type fuses from fuse block
- THX-374 THEXTON GM WIRE TERMINAL REMOVERS- $9.43
- Two tools remove Weather-Pack, Pack-Con and ECM terminals from connectors. Prevents damage to terminals and connectors. Heavy duty construction with durable plastic handles.
- THX-436 THEXTON WIRE INSERTION TOOL- $11.55
- For installing wires or cables through rubber grommets. Sharpe punch easily pierces thickest grommets. Hole in handle and pinch allows for easy feeding of wire through tool and grommet.
- Back To The Top Of The Page
2.CARBURETOR TOOLS
3.FEELER GAUGES
4.TERMINAL/FUSE TOOLS
- ATD-5295 ATD SPARK PLUG PLIERS- $5.38
- Designed to remove lead terminals from spark plugs quickly and easily. Plastic coated handles for shock resistance.
- KDT-135 K-D TOOLS INSULATED SPARK PLUG TERMINAL PLIERS- $8.06
- No more shocks with this special tool designed to remove cable terminals from spark plugs quickly and easily. Heavy duty handles double coated with Dielectric plastic for shockproof, sure grip operation. Jaws coated for extra safety.
- LIS-51500 LISLE NYLON SPARK PLUG WIRE PULLER- $2.95
- Helps pull plug wires quickly and easily without damage to wire or rubber protectors. helps prevent shock.
- THX-334 THEXTON SPARK PLUG WIRE PULLER- $11.49
- Removes frozen spark plug boots with a twist and a pull. Eliminates separated wires. Front tabs grip under boot, jaws firmly grip boot. Stubby design ideal for working in confined areas. Fits most standard boots. All steel durable construction and comfortable vinyl grips.
- THX-309 THEXTON SPARK PLUG REMOVER AND INSTALLER- $8.57
- Makes installing the hard-to-reach plugs easy. Reaches over, under and around obstructions. Flexible shaft allows turning at any angle. Eliminates cross-threading. Soft tip is stepped to grip terminal and porcelain. Non-slip handle. Length 9".
- ATD-2040 ATD EXTENDED SPARK PLUG SOCKET- $9.15
- Reaches 4-3/4" into deeply recessed engine blocks, including v-6. Has hex, 3/8" square drive and rubber insert.
- VERMONT AMERICAN SPARK PLUG TAPS
- VER-21140 10mm x 1.00($4.90), VER-21152 14mm x 1.25($7.79), VER-21164 18mm x 1.50($11.10).
- OTC-7154 OTC LONG HANDLE SPARK PLUG BOOT PULLER- $8.95
- What you've been looking for when trying to remove recessed spark plug boots. The extra-long handle does the job on all GM front wheel drive car engines. It gets a grip behind the baked-on boots and pulls them without damaging the wire.
- OTC-7078 OTC SPARK PLUG BOOT PULLER- (10)$42.50
- Baked-on plug wire boots are no longer a problem. Since all the pulling force is extended on the boot, not the wire. There is little chance of the wire being separated from the boot, a problem in the past that necessitated replacement of the wire.
- ATD-5299 ATD SPARK PLUG THREAD CHASER- $4.90
- Combination 14mm and 18mm chaser services practically all makes and models of cars. Cleans and restores threads, removes carbon and corrosion. Each end is slightly tapered for ease in starting plug hole
- KDT-730 K-D TOOLS SPARK PLUG HOLE THREAD CHASER- $5.99
- Fits 14mm and 18mm plug holes. 13/16" hex body size. Services practically all makes and models of cars. Cleans threads of carbon corrosion and metal. Band holds chaser firmly to spark plug socket wrench.
- THX-419 THEXTON GM ENGINE MOVING TOOL- $40.87
- This tool allows the engine to be tilted forward. Provides easy access to spark plugs, distributor caps, ignition coils, rack and pinion steering gear, power steering hoses, etc. Prevents damage to engine components, easy to install. Safely holds engine in place.
- LIS-51750 LISLE ADJUSTABLE SPARK PLUG WIRE PULLER - $23.95
- Jaws adjust to five positions allowing easier access to spark plug boots. Specially shaped, cushioned jaws grip the boot straight on or from the side. Plastic handle grips help prevent shock.
- LIS-50850 LISLE IGNITION SPARK TESTER - $6.25
- Quickly checks spark at plug wire. A handy tool to check ignition spark without removing the spark plug. The tool is specially calibrated to measure ignition voltage. Works on both standard and electronic ignition systems. Easy to use. Simply adjust calibration screw to proper gap size, attach spark plug wire to end of tester. Clamp tester on engine to ground. Crank engine and check for spark.
- Back To The Top Of The Page
5.SPARK PLUG TOOLS
- DISTRIBUTOR CLAMP WRENCHES
- Reach around obstructions to turn distributor lock nut with these double ended wrenches. each comes with two wrenches and 3/8" adapter. Use to install or adjust distributor. ATD-5630($8.60) Fits 1/2" and 9/16" lock nuts. Fits most popular sized distributor lock nuts. KDT-104($26.53) Fits 1/2" and 9/16" lock nuts. Fits most popular sized distributor lock nuts
- K-D TOOLS DISTRIBUTOR WRENCHES
- These wrenches fit most distributors with the same hex size as the wrench. KDT-2575 ($17.06) 1/2" SIZE, AMC 258-(6), CHRYSLER V8, FORD V8, 1966-1977 V8, INTERNATIONAL (4), 258 - (6). KDT-2576 ($18.75) 9/16" SIZE, GM 283 V8, 400 V8, 327 V8, 427 V8, 350 V8, 454 V8, 396 AND 396 V8, AMC 360 V8, 348 V8. KDT-2579($18.64) 13mm SIZE, FORD 2000cc - (4), 2800cc V6, 302 V8, 3.3L V6, CHRYSLER K CAR 4 CYL., 105 4 CYL.
- KDT-3197 K-D TOOLS 5.5mm FORD DISTRIBUTOR MODULE SOCKET- $6.00
- Easily removes and replaces mounting screws on Ford ignition modules that are attached to the distributor without removing the distributor. Use with 1/2" open or box wrench, or 1/4" square drive 1/2" hex socket. Plated for corrosion resistance.
- KDT-103 K-D TOOLS TOWER BRUSH- $6.77
- For cleaning all makes of distributor tower head sockets. Just insert tool and twist. Removes rust, dirt, and corrosion.
- KDT-124 K-D TOOLS REMOTE CONTROL STARTER SWITCH- $15.53
- Use to bypass ignition switch on any engine with a solenoid starter switch. Lets you crank engine while working in engine compartment. Extra long leads. Heavy duty construction. Connect from positive terminal of battery to energizing terminal of solenoid. Use for generator, starter, and electrical tests, setting ignition points, fuel pump tests, adjusting tappets and compression tests.
- KDT-2423 K-D TOOLS TWO IN ONE CURRENT INDICATOR- $16.32
- For 6, 12 and 24 volt systems. Measures both alternator and starter DC current and indicates direction of current flow without breaking into lines. Just hang meter on wire. Gauge is color coded to correspond with alternator and starter current readings. High visibility gauge. Compact design. Heavy duty construction. Starter current scale: 600-0-600. Alternator current scale: 75-0-75.
- Back To The Top Of The Page
6.DISTRIBUTOR TOOLS/STARTER TOOLS
- THX-367 THEXTON COIL TERMINAL ADAPTER- $7.48
- Fits GM, & Ford coils. Eliminates makeshift methods of attaching scope and test equipment. design allows GM (TACH) and (BATT) wires to be connected to adapter. Also connects into Ford coil cap. Fits GM HEI internal coil and Ford Electronic Ignitions.
- THX-404 THEXTON ADJUSTABLE IGNITION SPARK TESTER- $10.51
- Works on ignition systems from high energy electronic automotive systems to small engines. test for no start conditions and for spark strength. Adjustable gap allows for different spark gap requirements of different ignition systems from 0 to 40,000 volts. Gauge background makes spark easy to see for accurate measurement. Alligator clip securely fastens to ground. Screw assembly adjusts spark gap quickly and easily. Includes safety shield.
- THX-374 THEXTON GM COMPUTER COMMAND CONTROL WIRE TERMINAL REMOVERS- $9.43
- Removes Weather-Pack, Pack-Con, and ECM terminals from connectors. Prevents damage to terminals and connectors. 2 tools: Weather-Pack Tool: Slide hollow end of tool over terminal and apply twisting pressure. Pack-Con & ECM Tool: Slide blade into connector and depress locking tab on terminal.
- FORD IGNITION MODULE WRENCHES
- For 7/32" hex retaining bolts on Ford Ignition Module. May be used with 1/2" wrench. ATD-5640 ATD Tools($3.42), LIS-64650 Lisle($4.95).
- KAS-FM720A KASTER FORD IGNITION MODULE ADAPTER KIT- $12.33
- Special designed 25 degree offset ratcheting dual-ended wrench with 7/32" hex (5.5mm) on one end and a T20 Torx(R) bit on the other.
- THX-2800 THEXTON IGNITION COIL ADAPTER KIT- $132.88
- Test adapters connect to coil and coil harness for convenient hook-up of test equipment. Fits most foreign and domestic ignition systems including: AMC, Acura, BMW, Chrysler, imports, Ford(and imports), GM (and imports), Honda, Hyundia, Isuzu, Mistsubishi, Nissan, Subaru, Susuki, and Toyota. Comes in durable plastic case. Instructions included.
- Back To The Top Of The Page
7.IGNITION TOOLS
- LISLE EXHAUST AND TAILPIPE EXPANDERS
- Remove clamp grooves and round-out pipes. A practical tool that makes easy work out of a tough job. Step design gives big range. LIS-32500($27.95) For pipes 1-5/8" to 2-7/16" in diameter. LIS-32750($44.95) For pipes 2-3/8" to 3-1/4".
- K-D TOOLS EXHAUST AND RAILPIPE EXPANDERS
- Flare, shape and expand tailpipes to assure a tight fit and prevent exhaust leaks. Turn handle to adjust expander to diameter of pipe. Place on end of pipe and drive with hammer. remove and readjust. repeat hammering intill desired shape and size is reached. wear safety goggles. KDT-2269 For pipes 2-3/8" to 3-1/16" in diameter. KDT-2070($31.95) For pipes 1-7/16" to 2" in diameter. KDT-2071($23.60) For pipes 1-13/16" to 2-1/2" in diameter.
- LIS-32000 PIPE END SHAPER- $26.95
- Rounds out exhaust pipes that are crushed or bent in by inserting the point of the cone in pipe. Re-shapes pipes bent or flares out by placing big end over pipe.
- LIS-31500 LISLE EXHAUST/STRUT CUTOFF TOOL- $28.95
- Cuts pipe sizes 1-3/8" to 2-1/2" in diameter. Simple and quick set up. Four cutting wheels cut quick and clean, track perfectly. One hand operation, tighten by turning handle. Less than 1/3 turn cuts all the way around the pipe. also cuts out-of-round pipes.
- ATD-5720 ATD TAIL PIPE CUTTER- $36.81
- Cutting wheel on each roller for smooth tracking. Cuts pipes 3/4" to 3-1/4" (19mm to 76mm) in diameter. Effective in hard to reach areas. Works on all new-type thin wall exhaust and tail pipes.
- KDT-2031 K-D TOOLS EXHAUST AND TAILPIPE CUTTER- $43.18
- Completely adjustable for pipes 3/4" to 3" in diameter. Fifteen cutters give excellent tracking. Only 90 degrees of handle movement required. Gets into the tightest areas. Special lock-guard feature controls cutting depth, will not cut double-wall pipe.
- K-D TOOLS MUFFLER/TAILPIPE CHISELS- $10.88 Ea.
- Cuts through rusted, corroded tailpipe connections. Insert between tailpipe and muffler. Wear safety goggles. KDT-2072 10" Sharpe blade to separate pipes. KDT-2073 3-bladed splits open outside pipe.
- LIS-33000 LISLE TAIL/EXHAUST PIPE REMOVER- $16.25
- Works on both inside and outside rusted pipes. Saves serviceable exhaust components. Can be used with impact tool.
- KDT-715 K-D TOOLS UNIVERSAL NUT CRACKER TOOL- $40.24
- Capacity 7/16" through 3/4". Compound angle design with 360 degrees rotating cutter. Will work in places inaccessible to any other. Parallel action of pusher cracks nuts with no danger of damage to bolt threads. Cutter never touches the bolt. Rugged drop forged frame. chisel, steel ball, screw, and plunger replaceable. Length 6-3/4".
- LIS-32100 LISLE EXHAUST (DONUT) STRETCHER- $9.95
- Removes and installs rubber mounting ring style hangers found on many imports.
- Back To The Top Of The Page
