Special
|
- KAS-5458 KASTER 14-Pc. BRAKE CALIPER GUIDE PIN BIT WRENCH SET- $75 .58
- This set is a real time saver. It allows easy access to guide pins located on the wheel. Set contains the wrench and twelve 5/16" drive bits in sizes 6, 7, 8, 10mm, T40, T45, T47, T50, TORX(R) and 7/32". 1/4", 5/16", 3/8" and one extension, in a blow molded box.
- VIM-B91 VIM 2 Pc. GM CALIPER BOLT SET- $19.40
- These torx bit savers cover sizes: TX50, TX45 for use on GM vehicles.
- VIM-B90 3 Pc. FORD CALIPER BOLT SET- $29.10
- These torx bit saver tools cover sizes: TX40, TX45, TX50 for use on Ford vehicles.
- CALIPER TOOLS & CALIPER SOCKETS
- GM DISC BRAKE CALIPER TOOL
- Special wrench for installing and removing caliper. Length of arm designed for working in tight areas. 3/8" hex. ATD-8650($2.97) ATD TOOLS, KDT-2147($3.03) K-D TOOLS.
- ATD-8655 ATD BRAKE CALIPER SET- $10.30
- Removes and replaces the floating caliper mounting bolts. Three piece set includes one ATD-8652 3/8" (12mm) hex-3/8" square drive - GM socket, one 1/4" hex - 3/8" square drive - Ford socket and one 5/16" (8mm) hex - 3/8" square drive - GM socket.
- LIS-12550 LISLE BRAKE CALIPER SOCKET SET- $7.75
- For servicing disc brakes. Set contains three 3/8" square drive sockets with hex bits to remove and replace floating caliper mounting bolts. 3/8" and 8mm hex bits for GM and 1/4" hex bit for Ford.
- LIS-27740 LISLE BRAKE CALIPER TORX(R) BIT SET- $10.45
- Three 3/8" square drive Torx(R) bits for fitting GM and Ford disc brake caliper Torx(R) bol;ts. Sizes T40, T45, T50.
- THEXTON DISC BRAKE BLEEDER SCREW REPAIR KITS
- Fast, simple answer to broken or frozen bleeder screws. Just drill, tap and install. brass inserts provide new seat for screw. Eliminate need to replace caliper. Fits most single piston calipers from 1964 & up. Also for wheel cylinders on drum brakes. THX-562($3.41) 1/4" NPT, THX-563($3.07) 1/8" NPT.
- KDT-2116 K-D TOOLS DISC BRAKE LINING WEAR GAUGE WITH FRACTIONAL SCALE- $16.55
- Measures fraction of lining remaining on disc brake pads. Three scales cover the complete range of disc brake linings on American cars. Gives immediate indication of amount of lining remaining on disc brake pad. Makes check in most cases without removing caliper. Measures from 1/16" to 5/8", in 1/32 increments.
- OTC-714 OTC HORSESHOE LOCK RING PLIER- $29.95
- Designed to spread and remove horseshoe lock rings on hydraulic brakes, differentials and transmissions, and C.V. joints. Length 8". maximum spread 1-3/8".
- OTC-7103 OTC O RING/OIL SEAL PICK SET- $12.95
- Keep a set these picks in your tool box. Great time saver when finishing a stubborn O-ring or oil seal out of it's seat.
- THX-365 THEXTON UNIVERSAL EMERGENCY BRAKE TOOL- $15.85
- Compresses spring on emergency cable for replacing brake shoe arm. Fits all vehicles using cable/spring emergency brake assembly. Eliminates pinched fingers, frees one hand for replacing brake shoe lever.
- DISC BRAKE PAD SPREADERS
- KDT-TOOLS DISC BRAKE PAD SPREADER
- A must tool when installing pads. Spreads pads 3/4" to 1-11/16" and holds them in position when assembling caliper over rotor
- LIS-24400 LISLE DISC BRAKE PAD SPREADER- $8.95
- For installing pads on most domestic and import cars and light trucks. Makes changing pads easy. Tool compresses disc brake piston for easy pad installation..
- ATD-5050 DISC BRAKE PAD SPREADER- $9.37
- Compresses disc brake piston for easy pad changing on most cars and light trucks.
- LIS-48400 LISLE IMPORT CAR BRAKE CLIP TOOL- $7.95
- Designed for import cars with brake shoe hold-down clips. Removes and installs the brake clip and nail on brake shoes in seconds. Set tool head in the brake clip groove. Push tool to depress brake clip. Turn handle 1/4 turn to disengage clip from nail. Reverse to install.
- ATD-5060 DISC BRAKE PISTON TOOL
- Designed to rotate the parking brake activated piston back into the caliper cylinder when replacing worn pads on vehicles equipped with four wheel disc brakes. This tool will function on most import, Ford, Chrysler and some GM.
- ATD-7024 11 Pc. DISK BRAKE PAD & CALIPER KIT
- Magnetic socket adapter. Includes 8 adapters for brake assembles. Rotates pistons back into the caliper to provide clearance for the new pads. Prevents damage to the piston and boot. Kitt comes complete in blow molded storage case. Designed for use with Mercedes, BMW, Volkswagon, GM, Audi, Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4-wheel drive vehicles.
- Back To The Top Of The Page
- LISLE-11260 BRAKE SPRING PLIERS - $22.95
- Double ended tool for removing and installing brake springs. Use plier tips to stretch brake spring. Handle ends remove and install spring over anchor post. Skin-packed. Shipping weight 16 oz.
- ATD-5147 ATD 7-Pc. BRAKE TOOL SET- $34.86
- Seven piece set includes one brake spring compressor, one universal brake spring tool, three brake bleeder wrenches in sizes 1/4" x 3/8", 5/16" x 3/8" and 8mm x 10mm, two brake adjusting tools for servicing most foreign and domestic brakes. Comes packed in an organizer tray.
- ATD-5140 ATD BRAKE SPRING COMPRESSOR- $5.15
- Removes and replaces retaining washer on hold down springs quickly and easily. Place end over washer and make 1/4 turn. Reverse procedure to replace.
- KDT-285 K-D TOOLS BRAKE SHOE RETAINING SPRING TOOL- $8.25
- Removes and installs retaining spring 11/16" to 7/8" in diameter. Special socket grips retaining washer. Push and turn to remove or install.
- KDT-2773 K-D TOOLS BRAKE RETAINING TOOL- $7.32
- For compact vehicles. Removes and installs brake spring retainers 5/8" to 11/16" in diameter on small car drum brakes. Small socket fits into tight places. Push and turn to remove or install.
- KDT-2774 K-D TOOLS UNIVERSAL BRAKE SHOE RETAINING SPRING TOOL- $8.40
- Double-ended tool removes small and large car drum brake retaining springs. Fits sizes 5/8" to 11/16" and 11/16" to 7/8" diameter. Special socket griips retaining washer. Push and turn to remove or install.
- KDT-280 K-D TOOLS SHOE SPRING TOOL- $8.14
- For Bendix brakes. Use special socket end for removing return spring and other groove end for replacing spring.
- OTC-7069A OTC TRUCK BRAKE SPRING PLIER- $110.95
- Heavy duty truck brake spring plier with replaceable tip (OTC-202621). Provides the extra leverage and strength needed for servicing brake springs on many trucks and trailers. Huge jaw opening allows servicing of even the widest brake shoes. Length 26-1/4"
- ATD-5141 ATD BRAKE SPRING TOOL- $5.15
- Remove and replace Bendix brake shoe return springs. Plated, heavy duty drop forged steel. Place socket end over spring anchor and twist to remove. Hook notched end over spring and lift to install. length 9".
- KDT-2402 K-D TOOLS DRUM BRAKE SPRING TOOL- $7.85
- Removes and installs Bendix brake shoe return springs. Holder end removes spring from anchor stud. Hooked end slips spring back into place.
- ATD-5144 ATD UNIVERSAL BRAKE SPRING PLIERS- $31.75
- Forged alloy steel, chrome plated. Removes and replaces Bendix brake shoe return springs. Thin narrow points for straight-in-line pull on spring. Length 13-1/2".
- KDT-298 K-D TOOLS UNIVERSAL BRAKE SPRING PLIERS- $22.50
- Removes and installs shoe return springs on most drum brakes. Socket end removes spring from anchor stud. Notched end installs spring on anchor. Pliers remove and install the return spring to outside of brake shoe.
- LISLE-49900 GM SINGLE SPRING BRAKE TOOL - $19.95
- Releases tension on large GM single brake springs so brakes can be serviced. Several larger, late model GM cars use heavy single brake spring. The spring tension must be released to disassemble the brake to replace brake shoes, emergency brake cable, or service the brake spring and quickly releases the spring tension. The tool holds the spring in the open position so both hands are free to service the brake.
- LIS-44800 LISLE HEAVY-DUTY BRAKE SPRING TOOL - $11.95
- Designed for larger brake springs. The heavy-duty tool removes and installs larger brake return springs. Works on brakes with or without an anchor pin. Engage brake spring in tool head. Turn rear handle to lock on spring. Expand spring to install or remove. Front handle can be removed when working in tight places.
- Back To The Top Of The Page
- VIM-B82 FORD BRAKE CALIPER RETAINER REMOVAL TOOL- $12.35
- Designed to remove all ford brake Caliper Retainers including: F150-F350. Ranger, Aerostar and vans.
- DRUM BRAKE ADJUSTMENT TOOLS
- Most popular and universal type. Special shape gives greater application. Speeds starwheel adjusting. ATD-5142($8.49) ATD TOOLS. LIS-50700($4.65) LISLE TOOLS. KDT-287($5.69) K-D TOOLS.
- ATD-5138 ATD ONE-HAND-BRAKE TOOL- $11.69
- Just one hand, one simple motion this tool pushes back the retaining plate and adjust the brake star wheel.
- KDT-295 K-D TOOLS OFFSET BRAKE ADJUSTING TOOL- $7.68
- Will work on most brakes but is specially adapter for Corvair, Chevelle, Tempest and other small cars.
- KDT-282 K-D TOOLS TRUCK BRAKE ADJUSTING TOOL- $10.18
- For trucks with mechanically adjustable brakes. Designed to clear axle housing to reach slot in top of backing plate on some trucks.
- OTC-7248 OTC TRUCK BRAKE ANCHOR PIN PRESS- $150.95
- With this rugged C-frame press, you can easily remove the often rusted truck brake anchor pins. Mechanical screw power of the 7248 does the job quickly and with little effort. With this press you can handle truck brake pins up to 1-1/4" diameter. Wt., 9 lbs., 6 oz.
- LIS-18800 LISLE BRAKE CYLINDER RETAINER REMOVER- $14.45
- For GM X and J-body cars. Expands and holds this special retainer so the brake cylinder may be removed. Replace the retainer by reversing the procedure.
- ATD-5146 PARK BRAKE SPRING COMPRESSOR- $8.97
- Remove/Install lever cable attached to brake shoe on cars and trucks. Compresses spring on emergency brake cable for fast and easy replacement of brake shoe arm to cable. End of tool fits between spring and cable end, plier compresses spring to allow emergency brake lever to be installed.
- ATD-5148 GM REAR BRAKE CYLINDER CLIP REMOVER- $6.42
- Removes retainer clip on rear wheel cylinders on many late model cars and trucks.
- ATD-5149 ANTI-LOCK BRAKE SYSTEM CODE RETRIEVAL KEY- $2.28
- Jumps between A and H terminals on ALDL connector to retrieve trouble codes from the ABS microprocessor.
- VIM-B10 BRAKE SHOE RETAINER SPRING TOOL- $5.20
- Designed to remove and easily replace the brake shoe retainer spring on trucks. Tool fits into coil of spring and provides good leverage to engage or disengage the hook arm of the spring with no difficulty. Off-set handle keeps clear of brake and wheel components. Plastic handle for good grip and comfort.
- LIS-40800 LISLE PARKING BRAKE CABLE REMOVER -$11.95
- Makes parking brake cable removal easy. Double ended tool will quickly remove parking brake cables from the brake backing plate and the chassis mounting bracket. Cylindrical tool ends compress the prongs on the spring fastener for easy disassembly. Tool can be used with one hand so other hand can pull the cable. Use the smaller end for Ford Escort, Topaz and Tempo. Use the larger end for other vehicles.
- ATD-5142 DRUM BRAKE ADJUSTMENT TOOL - BRAKE SPOON
- Most popular & universal type. Special shape gives greater application. Speeds starwheel adjusting. Fits all brakes, except Chevrolet. One end square cut, the other end tapered 22 degrees for added reach. Hex stock, forged heat-treated plated 9" (229mm) OAL.
- Back To The Top Of The Page
- ATD-5143 ATD BRAKE BLEEDER WRENCH- $4.90
- 5/16" and 3/8" hex openings for GM cars since 1055, plus Lincoln and Ford with ball joint suspension.
- KDT-283 K-D TOOLS BRAKE BLEEDER WRENCH- $7.23
- Bleeds air from brake cylinders with 3/8" or 5/16" hex head bleeder screws. Box end lets you see when fluid starts to flow. Fits most GMs.
- LIS-10950 LISLE TOOLS BRAKE BLEEDER WRENCH- $6.75
- For all cars with 1/4" and 3/8" bleeder nut. Special offset handle. Makes bleeding brakes a simple task.
- KDT-291 K-D TOOLS BRAKE BLEEDER WRENCH- $7.82
- Design provides easy access. High offset brake wrench with 1/4" and 3/8" 6-point openings.
- KDT-286 K-D TOOLS BRAKE BLEEDER WRENCH- $9.10
- Same high offset as KDT-291, except 3/8" and 7/16" 6-point openings.
- KDT-2811 K-D TOOLS GM X-BODY BRAKE BLEEDER WRENCH- $10.28
- For GM X-body and other late model cars with 8mm and 10mm hex fittings. Easily reaches brake bleeder nut with offset handle.
- PLE-70060 PLEWS BRAKE FLUID PUMP- $26.77
- Designed to pump most non-corrosive fluids from one gallon cans such brake fluid, power steering fluid, etc. fastens directly onto can. Despenses approximately one ounce of fluid per stroke. Comes with a 36" hose complete with check valve mounted in the metal nozzle providing an air tight seal. Furnished with four cap sizes to fit most standard one gallon can designs and a 3" extension for taller, deeper cans.
- LIS-47400 BRAKE SPRING WASHING TOOL -$6.95
- Fits both large and small washers. Troublesome brake shoe retaining spring washers can now be easily removed and then reinstalled. Wide window allows better visibility to align the nail and washer slot.
- LIS-75200 LISLE VACUUM TESTING/BRAKE BLEEDING KIT -$
- Comes with LIS-75000 Vacuum Pump and complete accessories for vacuum testing and brake bleeding. Pump is made of one-piece zinc die cast material for durability and improved performance.
- Back To The Top Of The Page
- ATD-5125 ATD BRAKE BLEEDER TANK- $146.06
- 4 quart capacity. 10-1/2 ft hose. Feature quick disconnect coupler, shut-off valve and pressure gauge. Portable tank fills and bleeds both standard and power brakes in a single operation. Pressurized with built-in hand pump.
- ATD-5121 ATD DUAL BRAKE BLEEDER ADAPTER- $13.15
- Domestic cars 1967 to present with dual cylinders sizes 3-3/16" to 6". Use with ATD-5125.
- ATD-5126 ATD PLASTIC RESERVOIR ADAPTER- $37.37
- For late GM and Chryslers with plastic reservoir brake systems. Use with ATD-5125.
- ATD-5150 ATD ONE MAN BRAKE BLEEDER- $8.44
- This simple and efficient tool with retaining strap will not dislodges under pressure. Clear plastic tube enables constant visual check. One way check valve prevents air from reentering brake lines. Works on all cars.
- KDT-2222 K-D TOOLS BRAKE BLEEDER TANK- $314.13
- Features safety pressure release valve to protect the operator and to prevent damage to the diaphram. Shut-off valve at the quick disconnect coupler saves the loss of fluid and makes it convenient to use the unit as both a one-man bleeder or as a source of brake fluid for topping off master cylinder. Capacity 7 quarts. With 10-1/2 ft hose. (for use with DOT 2, 3, 4, and 5 brake fluids only.)
- BRAKE BLEEDER ADAPTERS
- fits KDT-2222 and ATD-5125. KDT-2216($38.35) DUAL BRAKE BLEEDER ADAPTER. KDT-2417($61.12) BRAKE BLEEDER ADAPTER. Large dual master cylinders plate size 3-1/4" x 8-3/4". KDT-3297($40.81) UNIVERSAL ADAPTER. For plastic reservoirs 9/16" to 2-3/4". KDT-3353($63.49) LATE MODEL GM & CHRYSLER
- THX-346 THEXTON MASTER CYLINDER BLEEDER KIT- $12.33
- Adapter assortment fits most American cars. Built-in residual check valve stops back flow of fluid. Clip holds bleeder tubes in reservoir. Packed in plastic box. Includes instruments.
- MTY-6820 MITYVAC BRAKE BLEEDING KIT- $39.01
- Provides a clean and quick method for bleeding the fluid lines in automotive systems. Transforms brake bleeding into a simple one-person task. Provides a clean and quick method for bleeding the hydraulic lines of most automotive brake systems, including some anti-lock brake systems. Kit includes a repairable Mityvac, pump reservoir jar with transfer lid and storage lids, brake bleeding adapter package, transparent plastic tubing and the Mityvac 110+ page user's manual.
- SHK-S61 SHARK VACUUM BRAKE BLEEDER- $293.15
- This bleeder does not allow any spillage of brake fluid. Bleeding is a one man job with this tool. No special adapter needed. It works on all ABS systems and will not damage seals. It is air operated.
- Back To The Top Of The Page
- BRUSH RESEARCH FLEX HONES
- There is a flex hone to meet just about any honing requirement including brake work. Thy are fast, efficient, unbreakable and outlast other stones. Hone life is in excess of 1,000 cylinders. Set up is not required, use standard 3/8" electric hand drill. Each flex hone size works down to the next smaller size.
- Brake Cylinder Hone (8" OAL) 180 Grit
Brush Research Size Diameter BRM-BC7/8($17.90) 7/8" (22MM) .787" (20MM) BRM-BC1($19.10) 1" (25MM) 7/8" (22MM) BRM-BC1-1/8($21.08) 1-1/8" (29MM) 1" (25MM) BRM-BC1-3/8($22.23) 1-3/8" (35MM) 2-3/8" (29MM) - Disc Brake Cylinder Hone (5" OAL) 180 Grit
Brush Research Size Diameter BRM-DBC2-1/2($28.90) 2-1/2" (64MM) 2-1/8" (54MM) BRM-DBC3-1/8($35.23) 3-1/8" (79MM) 2-3/8" (70MM) - ATD-5010 ATD BRAKE CYLINDER HONE- $8.73
- Designed to do a professional job. A three stone hone for fast honing. Flexible drive shaft for ease of operation. Hones all master cylinders and wheel cylinders right on the car. Straight bore or blind end. Range 13/16" to 2-3/4" diameter.
- KDT-267 K-D TOOLS VW BRAKE CYLINDER HONE- $16.89
- Two stone model. For VW and all cars with brake cylinders from 15.875mm to 25.4mm (5/8" to 1") in diameter.
- KDT-265 K-D TOOLS BRAKE CYLINDER HONE- $15.96
- Standard model. Hones all master cylinders and wheel cylinders with straight bore or blind end - 13/16" to 2-3/4" in diameter.
- LIS-10000 LISLE BRAKE CYLINDER HONE- $14.45
- Controlled pressure makes it possible to clean and polish or hone with just one grit of stones. Three stones for stability and speed. Square ends of stones hone to the end in step-cut and blind-end cylinders. Flexible driver makes it easy to do the job right. Stones are not harmed by brake fluid or alcohol. Range 3/4" to 2".
- LIS-10500 LISLE MIGHTY-MITE BRAKE CYLINDER HONE- $13.95
- Works in most cylinder diameters from small foreign car wheel cylinders up, including standard blind-end and step-cut cylinders, small engine cylinders, idler bushings, etc. Range 9/16" to 2-1/2".
- AMM-1650 AMMCO BRAKE CYLINDER HONE- $32.33
- Only one adjustment. Slide lock ring into position and you are ready to hone with extra heavy duty flexible drive. Range 3/16" to 1-1/2".
- LIS-10400 LISLE DISC BRAKE HONE -$15.95
- For 1 1/2" to 3 1/8" disc brake cylinders (38.1mm to 79.3mm). Special abrasive pads polish the cylinder without cutting. Controlled pressure, 3 abrasives and flexible driver give good stability and speed. Stones are 1" long.
- LIS-22070 LISLE BRAKE CYLINDER WRENCH -$3.45
- Removes the wheel cylinder on late model GM cars. Tool removes 2 E8 Torx(r) bolts that hold the wheel cylinder on the backing plate. Angled, offset design allows easy access unrestricted areas. Reaching the 2 bolts is tough, they are hidden behind the shock assembly. Slip-on vinyl handle provides a good grip.
- Back To The Top Of The Page
- CEN-6496 CENTRAL DIGITAL ROTOR/BALL JOINT GAUGE- $377.99
- Check ball joints and rotors. With two pointed anvils and a 5" range the axial play in a ball joint can be measured. Rotor wall, thickness and scores can also be checked. Easy to read inch/metric convertible digital display. Range 0-5,000"/0-125mm. Graduations .001"/.01mm.
- CEN-6469 CENTRAL DIGITAL BRAKE DRUM GAUGE- $594.77
- Features easy to read digital display for easier and improved service and sales to customers. Adjustable depth stops and pointed anvil allows pre-inspection of scores and bell mouth. Push button conversion between inch and metric reading lets all drums be measured. Range 2.400" - 14.250"/60-360mm. Graduations .001"/.01mm.
- CEN-6459 CENTRAL BRAKE FORCE ROTOR GAUGE- $404.98
- This provides digital accuracy in measuring drums up to 14.25" as well as rotors and ball joints. pointed anvils measure both scored and unscored surfaces. Readings in inch and metric. Range is 0-2.25" in .001" graduations. Depth of measuring arms is 3.25". Comes with SR44 battery and protective storage case.
- CEN-6479 CENTRAL DIGITAL WHEELS ON ROTOR GAUGE- $397.90
- Measure rotors without removing the wheel. Use this gauge to find brake jobs you're missing. Check rotors while doing under car work to increase brake work profits. Range 0-3.250"/0-80mm. Graduations .001"/.01mm.
- AMM-8650 AMMCO BRAKE SHOE SETTING GAUGE- 53.32
- For passenger cars, light trucks, RV's and trailers. Quickly gives correct lining-to-drum clearance before drums and wheels are installed. Transfers drum diameter directly to brake shoes. Used on all Bendix type fixed anchor brakes and cars using self-adjusting brakes. No need to back car up to adjust brakes. Handles diameters 6-1/2" to 14-1/4".
- AMM-8500 AMMCO BRAKE DRUM MICROMETER- $285.42
- Measures drums on or off the lathe. Checks out-of-roundness as well as diameter. Shockproof easy to read dial. A precision micrometer with a range of 6" to 16-1/8".
- AMM-8500-50 AMMCO METRIC BRAKE DRUM MICROMETER- $285.42
- Calibrated in metric. Measures drum diameters from 152.4 to 406.575mm. Graduated in 0.1 increments. Measures drum on or off the lathe. Checks out-of-roundness as well as diameter. Shockproof, easy to read dial.
- CEN-6478 CENTRAL BRAKE DRUM WEAR LIMIT GAUGE- $225.35
- For cars and trucks. Pointed contacts for pre-inspecting scored drums determines if it can be safety machined. Laser engraved 1/32" and 1mm graduations to measure actual drum. Range 6" - 22"/150 - 560mm.
- CENTRAL DISC MICROMETERS
- Central provides a choice of disc brake micrometers in English and metric calibrations. Specially designed for today's larger size rotos. Extra deep - 3-1/2" throats make it easy to measure across the entire braking surface, plus measurements for thickness, thickness variation and score depths. Features I-beam, drop forged fame construction, carbide faced spindle, friction stop, spindle lock and easy to read graduations. CEN-6202($132.89) .300 to 1.300" range. CEN-6203($132.89) 1.000 to 2.000" range. CEN-6212($120.92) 7 to 32mm range.
- CEN-6302 CENTRAL DISC BRAKE GAUGE- $141.35
- This precise, direct reading measurement gauge has an extra deep, 3-1/2" throat for use on or off the vehicle. The I-beam frame construction makes it durable. The pointed anvil allows grooves to be measured. Standard is included. The range is .300-1.200" graduations of .001. Reading 0-100.
- KDT-2324 K-D TOOLS BRAKE LINING INSPECTION GAUGE- $16.21
- Accorately measures, in graduations of 1/64" the amount of lining remaining up to 1/2". meets vehicle inspection code requirements. Works on trucks, buses and passenger car brakes.
- KDT-2112 K-D TOOLS DISC BRAKE ROTOR GAUGE- $45.10
- Two gauges in one. Measures thickness, wear and score depth of rotor. Calibrated in (.010") increments. Quick and less costly than micrometer method. use with runout indicator. Range .300 to 1.300".
- KDT-3377 K-D TOOLS BRAKE RESETTING GAUGE- $50.29
- Set to drum size, the patented gauge automatically shows correct shoe adjustment. Positive lock assures accuracy. Can also be used as drum gauge. For use on cars with brake drum diameters of 6-1/2" to 14-1/4".
- AMM-9494 AMMCO TRUCK BRAKE SHOE SETTING GAUGE- $436.77
- Use for both air and hydraulic brake systems with internal adjusters. Gauges drums ans sets shoes up to 22" in diameter. Shoe clearance is precisely set by built-in micrometer, which allows a clearance of 0" to 0.100".
- Back To The Top Of The Page
